IPV4_SECURE_UNICAST

Allows a consumer to start a simulation session.
The input of the simulationSessionStart operation shall contain the initial time of the session..

Allows a consumer to stop the current simulation session.

The applicationTime shall be not before than N seconds from the current time, where N is a configurable parameter tuned on provider platform (e.g. 10 seconds)..

Enables to activate a sector mapping: the supervisor selects a mapping (next or pre-defined mapping) that will replace the current mapping of the concerned ASTUSectorConfiguration.
The supervisor may also choose to revert back to the pre-defined default sector mapping. If not, the input parameters shall be the identifier and the state (next or pre-defined) of the origin sector mapping.
As a consequence, the parameter sectorMappingId is MANDATORY when the parameter revertToDefaultMapping is not filled or set to FALSE (but if revertToDefaultMapping is set to YES, sectorMappingId is not needed)..

Enables to modify a current mapping or a next mapping of a given ATSUSectorConfiguration..

Enables to load a pre-defined mapping as being the next mapping of a given ASTUSectorConfiguration.

The input parameters shall be:
- the ATSUSectorConfigurationIdentifier,
- the identifier of the sectorMapping.
.

Allows a consumer to modify the radio frequency assigned to control responsibility(ies):
- either by selecting a new radio frequency,
- or by reverting back to the predefined value (off-line defined) of the radio frequency assigned to the given control responsibility (if it has been on-line updated before).

The input parameters shall be:
- the value of the new radio frequency and the controlResponsibility(ies) where the indicated frequency shall be assigned,
- or the controlResponsibility(ies) where the default frequency shall be assigned.

When the aim of this operation is to :
- apply a new frequency to one or several Responsibilities, frequency should be filled
- revert to default frequency for one or several Responsibilities, revertToDefaultFreq should be set to TRUE and frequency shouldn't be filled
.

Enables to unlock a previous manual ARES activation status.
The input parameters shall be the originator and the ARES name. .

Enables to update the following ARES data:
- the status (activated or deactivated),
- the comment associated to the ARES.

The input parameters shall be the originator, the ARES name and the ARES status..

Enables to unlock a previous manual CDR status.
The input parameters shall be the originator and the CDR identifier (airway name and names of the start and last points of the CDR)..

Enables to lock the CDR status to open or closed.
The input parameters shall be the originator, the CDR identifier (airway name and names of the start and last points of the CDR) and the CDR status..

Allows to add a timesheet into an ARES timetable to define new activation periods.
The input parameters shall be the originator, the ARES name and the timesheet data containing the activation levels, an activation time period, and optionally a periodicity..

Allows to add a timesheet to a CDR.
The input parameters shall be the originator, the CDR identifier (airway name and names of the start and last points of the CDR) and the timesheet data containing an activation time period, and optionally the activation levels and/or a periodicity..

Allows to remove an existing activation periods timesheet from an ARES timetable.
The input parameters shall be the originator, the ARES name and the identifier of the timesheet to remove..

Allows to remove an existing activation periods timesheet from a CDR timetable.
The input parameters shall be the originator, the CDR identifier (airway name and names of the start and last points of the CDR) and the identifier of the timesheet to remove..

Allows to update an existing activation periods timesheet for an ARES.
The input parameters shall be the originator, the ARES name, the identifier of the timesheet to update and the timesheet data containing the activation levels, an activation time period, and optionally a periodicity..

Allows to modify the current configuration of the runways for an aerodrome of a given Aerodrome Group.
This operation enables an eligible user (normally a supervisor) to modify the following data of a given runway or of the runway(s) of an aerodrome: landing and/or take-off rates, IAP in operation and operating mode (open or closed).
It is also possible to revert to default rate values of runway(s) if no rate value is provided in the operation..

Allows replacing the current Aerodrome Group Configuration with another given aerodrome group configuration.
The user may activate an offline predefined aerodrome group configuration, activate the one previously defined as the Next one or revert back to the default one.

When the aim of this operation is to :
- activate an offline predefined aerodrome group configuration, aerodromeGroupConfigName should be filled with the name of the configuration,
- activate the next aerodrome group configuration, aerodromeGroupConfigName should not be filled,
- revert back to the default aerodrome group configuration, aerodromeGroupConfigName should not be filled and aerodromeConfigurationOrigin should be DEFAULT.
.

Allows removing the fact that an aerodrome group configuration is identified as the next one..

Allows modifying the configuration parameters of an aerodrome.

The 3 possibilities given by this operation are :
- revert to default the aerodrome Altitude Correction
- revert to default the aerodrome Transition Level. In this case, defaultAltitudeCorrection should be set to FALSE
- modify one or several of the following parameters : transitionLevel, altitudeCorrection, modeSCapabilityState. In this case, revertToDefault should not be filled

aerodromeGroup is ignored by CCS..